| Thank you for
purchasing a BRITELYT product. This
precision handcrafted product has
been manufactured for BriteLyt.
With a little care, this stove will
serve you a lifetime. (You can even
will it to your heirs c'mon, they
deserve it.) VIDEO HOW TO PAGE STOVE ASSEMBLY: SEE THIS PAGE FOR STOVE ASSEMBLY
1. Take stove out of box...
Stove comes pre-assembled.
2.
Look over stove and see that nothing
is missing, funnel included SEE THIS PAGE.
****DO
NOT LEAN DIRECTLY OVER STOVE(Emits
large preheater flame from part STV-226)*******
***LEAVE
FRAME ON STOVE, DURING LIGHTING
PROCESS)****
ALWAYS
REMEMBER -- SAFETY FIRST!!!!
-- LIGHT IT OUTDOORS
FAMILIARIZE
YOURSELF WITH ANY STOVE AND/OR
LAMP BEFORE OPERATING.
!! WASH OUT TANK (use water or Fuel) BEFORE USING !!
OPERATING
DIRECTIONS: Optical and mechanical check:
(CHECK FOR LEAKS
FIRST!!! Fill stove &
add pressure to detect any leaks) Also see this page
(1)
Fill the stove with KEROSENE,
or the fuel you like to use...
DO NOT
OVERFILL.
It should burn for 4 - 6 hours.
Remove Fuel Cap/with gauge. STV-149.
Tighten the filler(STV-149 see photo 9 below) and
bleeder cap(# 13) (the rough feeling,
round things), by turning clockwise.
(To the right - part STV-149...
same as lantern part#149). See
photo below 1. Make sure you put frame back on stove before using: DO NOT DO THIS WITH STOVE WORKING.
Photo
1 
________________________________________________________________
(2)
MAKE SURE
KNOB IS IN THE OFF position (
see part STV-40 in photo)...,
turn clockwise (stove should be
in the off position from the factory.) Look
into the hole on the mixing tube
to see if needle(#68) is sticking
out of the # 50. See photos 1A
and 1B below.
Photo1A
Photo1B 
_______________________________________________________________
(3)
Holding the tank STV-118, (shiny
thing), pump to the red mark.(
Part # 6 )
See
photo 2 below. To see red mark go to photo 9 below.
Photo
2
_________________________________________________________________
(4)
Apply Flame (match or cigarette
lighter) next to big hole in part
# 220 or under #220(next to the 2 holes)open part # 223 (see photos
3,3A,& 4) and then open preheater
all the way.
Photo 3
Photo 3A 
Photo
4 
***BE
CAREFUL!!! PREHEATER
WILL THROW OUT LARGE
FLAME!!***
See above photo 4
______________________________________________________________
(5)
Allow stove to PREHEAT (using
oil-based fuels) for approx. 60
seconds - 1-1/2 minutes. (Preheating
time is determined by atmospheric/altitude
conditions, and Fuel gas type
fuels about 50 seconds or less.!!WARNING!!
If insufficient preheating
time will cause raw fuel to come
out of -(# 50)
and make large flame..
When
using diesel oil it
may take 2 ½ min. to pre-heat,
using Biodiesel
can take 3 ½ min. to pre-heat. Photo
below 5,
also insufficient preheating
time (when you turn the stove
on)) can cause a buildup of fuel
in the mixing chamber (located
below the screw that holds the
burner assembly in place), and
may look like a leak.
Photo
5 
****YOU MAY NEED TO ADD PRESSURE,
during preheating time!!) see
above photo 5.
_________________________________________________________________
(6)
AFTER 60 seconds....(preheating).....TURN
ON/OFF(STV-40) KNOB COUNTER-CLOCKWISE
(slowly), and LISTEN FOR STOVE
TO START OPERATING. You
MAY or MAY NOT SEE A FLAME
there will be a flame from preheater
look for one on the burner ( the
thing with holes in it ).
When
stove is started, TURN OFF THE
PREHEATER (223-flip it back into position).
See photo below 5 & 6
Photo
5
Photo
6
________________________________________________________________
(7)
PRESSURIZE STOVE TO DESIRED PRESSURE (Part # 6).
(Stove will build it's pressure
to about 1 & 1/2 bars).
It will hold pressure, so it is
not necessary to pump stove on
continuous basis. ADJUST
STOVE TO DESIRED FLAME OUTPUT ( use part STV-40 ).
See photos below 7,8 & 9.
Photo
7
Photo
8 
Photo 9 
________________________________________________________________
If you
Preheat with alcohol use cup (tray) its on top of the burner see below (photo 10)
Photo 10 
_________________________________________________________________
Preheater Direction
* Remember to always use battery operated smoke detectors and carbon monoxide detectors in the home. It is prudent to protect yourself from any potential hazards of using ANY fuel burning appliance in your home. Do not use stoves inside home.
_________________________________________________________________
Upkeep of lanterns and stoves:
1.Do
not store fuel in lantern or stove
for long periods of time.
2.
When using " Bio" fuels clean
out tank and jets by adding some
fuel cleaner (like carburetor
cleaner) with your fuel in the
lantern or stove. Use 4 caps full
of a carburetor cleaner to 12
oz's. to a tank.
2a.You
can also use a half of a tank
of Coleman-type or similar type
of fuel in the lantern or stove
tank. Do this in the above in
2.and 2a. after 10 tanks full
of bio fuels or less.
3.
All other fuels except Coleman
type fuels - use carburetor cleaner
in the fuel (4 caps to a tank
full of fuel, every 10 fill ups
or less).
4.
Tighten up the # 50 always check
this part, when replacing a mantle,
make sure the part # 33 has not
dropped down close to the # 50.
Raise # 33 high as you can for
optimum performance. Most problems
with the lantern will be caused
by these two (2)....items # 50
and # 33.
5.
Preheater
Direction above photo:
Stove....Make sure you preheat
the area as shown in our stove
instruction page on this site,
and preheat long enough. (preheat
time approx: 50 sec. to 90 sec.)
Stove Breakdown and Replacement Parts Price List
|
